Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Installation for Arvada Homeowners
A gate that doesn’t open is a problem. A gate that was never hung right, or that gets bolted to a post set too shallow for the Front Range’s freeze and thaw cycles, is a bigger one. Most yards here sit on clay soil that swells in spring and shrinks in late summer, and gates hung without that movement in mind start dragging, sagging, or tripping the operator within a season or two. We do gate installation in Arvada with that in mind: proper footing depth, true posts, and operators matched to the actual weight and travel of the gate. Our technicians have up to experience across nine gate brands, and we handle residential and commercial systems on the same visit.
We answer 24/7. Fast dispatch, 7am-7pm, Sunday through Friday. For a new install or a full replacement, the first step is a free on-site measure and a written price. Call (844) 761-1390 to set it up.
Automatic Gate Installation
Automatic Gate Installation is the whole job from the ground up: footings poured, gate hung, operator wired, safety devices mounted, and everything tested against the driveway it serves. You need it when a manual gate has worn out or a new property has no gate at all, and you want it to open from a remote, keypad, or vehicle sensor rather than by hand. We handle the operator, the power run, the control board, and the safety edges so nothing gets handed off to another contractor mid-job. Automatic gate installation in Arvada is a measured, scheduled job rather than a same-day repair, and the price is set by the written estimate before any work begins. A full automatic setup typically runs $3,800-$9,500 depending on gate size, operator class, and whether a power run is needed. We’re familiar with LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule operators.
What a Full Automatic Setup Covers
We measure the opening, test the soil and grade at the post locations, and set footings to proper depth before anything is hung. The operator, control panel, and safety sensors are wired and tested together so the gate reverses correctly and the board isn’t fighting a bad sensor. You get a written scope before we start and a final walkthrough after.
Residential and Light Commercial Operators
A single-family gate and an HOA entrance with a keypad and loop detector need different hardware, wiring, and safety devices. We size the operator to the gate it actually has to move, not to what’s on the shelf. Heavy-duty platforms like DoorKing and FAAC are part of that range, so a multi-unit property doesn’t need a different vendor.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Gate Installation Services
Gate Installation Services cover the full scope from site measurement through final testing, whether you’re replacing a gate that was never right or starting from bare ground. You need them when a gate has been hit, when posts have heaved out of line, or when a property is being built out and needs an entry that actually works. Gate Repair Arvada handles repair and installation under one roof, so a diagnosis visit can turn into a plan without a second call. Installation in Arvada is priced per job from the written estimate. A basic single-swing residential gate with hardware typically runs $1,900-$4,200 before the operator; add automation and that range climbs. Our technicians have up to experience and we work across nine gate brands including Linear, Viking, and Ghost Controls.
Measure First, Quote Second
Every install starts with an on-site measure: gate width, post spacing, grade, and the direction the gate needs to swing or slide. That’s what keeps a quote from moving after the work begins. The written estimate sets the final price, and nothing starts until you’ve agreed to it.

Repair or Replace
Not every problem needs a new gate. If the frame is sound and only the operator, control board, or safety sensor has failed, we say so and quote the repair. When posts are heaved or the frame is bent beyond straightening, replacement is the honest answer.

Electric Gate Installation
Electric Gate Installation puts a powered operator, wiring, and access control on a gate that opens without a hand on it, and it’s what most homeowners mean when they say they want an automatic entry. You need it when a manual gate gets used dozens of times a day or when an existing operator is obsolete and no replacement board fits. We install the motor, run the power and low-voltage control wiring, mount the safety sensors, and set the access control board so remotes, keypads, and loop detectors all talk to it in the same language. Electric gate installation in Arvada isn’t a same-day job; it’s scheduled after a free measure. A full electric install usually runs $4,200-$10,500 depending on operator class and whether underground power needs to be brought to the gate. We’re familiar with FAAC, BFT, DoorKing, and LiftMaster among the nine brands we work with.
Power, Control, and Safety
The power run and the low-voltage control run are separate jobs and both have to be right. Safety sensors and reversing devices are mounted and tested so the gate stops for a car, a child, or a dog rather than trusting a remote. The control board is set to the gate’s actual travel and weight, not a factory default.
Access Control From the Start
Keypads, remotes, and vehicle loop detectors are easiest to set up when the board is fresh and every wire is labeled. We install the access control as part of the same job so nothing is added later in a way that fights the existing wiring. If your gate fails at any point afterward, our gate repair Arvada team can pick it up from there.
Driveway Gate Installation
Driveway Gate Installation is the entry that controls a car, a truck, or a trailer, and it takes the most abuse of anything on the property. You need it when a driveway widens or straightens, when a gate has been knocked by a vehicle, or when a new build needs an entry that will hold up to daily traffic. The width and weight of the gate you want is the first decision: a driveway gate has to swing or slide clear of the drive without hitting a parked car, and it has to clear the ground on a slope. We install driveway gates in Arvada sized to the actual opening, with footings poured to proper depth and operators matched to the load. A driveway gate install typically runs $3,500-$8,900 including the operator, and the written estimate sets the final number. We handle Linear, Viking, and Ghost Controls operators alongside the commercial-grade platforms.
Footings and Grade
Arvada’s clay soil moves, and a driveway gate that’s hung on a shallow post will follow it. Footings go deep enough to hold through the freeze and thaw, and post caps are set so water runs off rather than pooling at the hinge. We check grade before we pick the gate direction so the gate doesn’t drag on the highest point of the drive.
Clearance and Swing Direction
Swing direction and total clearance get sorted out on the measure, not after the posts are set. A gate that swings into the drive is convenient for a single car but trouble on a narrow approach. We plan the arc so the gate has room to travel at the worst-case vehicle position.
Sliding Gate Installation
Sliding Gate Installation is the right call on a tight driveway or a slope where a swing gate can’t clear, and it handles long spans that a swing gate struggles to carry. You need it when there’s no room to swing, when the grade drops away from the house, or when the driveway is too long for a swing operator to hold. A sliding gate rides on a track or cantilever system with guide rollers and a rack-and-pinion operator, and every component has to be set true or the gate will drift off the track over time. We install sliding gates in Arvada with guide posts set true, track or cantilever hardware, and operators sized for the weight of the gate. A sliding setup typically runs $4,000-$9,800 depending on leaf length, operator, and access control. Every one of those jobs is scheduled from a written estimate rather than promised same-day; our technicians have up to experience on this hardware, including Viking and Linear operators.
Cantilever vs. Ground Track
A cantilever gate needs no track across the driveway, which is cleaner for a long entrance and better where the ground heaves. A ground track is simpler to install but needs soil that doesn’t swallow it each winter. We pick based on how the driveway drains and what the gate has to clear.
Getting the Gate to Stay on the Track
Most gate failure is rollout, not operator failure. Guide rollers, catches, and the track itself are set with clearance so the gate stays aligned even after soil shifts. That attention to alignment up front is what keeps the sliding gate from needing a repair call a year in.
Gate Opener Installation
Gate Opener Installation is the job of adding a powered operator to a gate that’s already hung, and it’s the fastest way to make a heavy manual gate usable. You need it when a manual gate has become a chore, when a board has failed on an older opener and no replacement fits, or when you’re adding a gate to an entry that never had power. We install the operator and wire it to the control board, mount the safety sensors and reversing devices, and set the stops so the gate travels the exact distance it needs to. There’s no same-day promise here; the work is measured, ordered, and scheduled. A gate opener install in Arvada typically runs $2,400-$6,500 depending on operator class and the power run. The written estimate sets the final price before any work starts. We work on DoorKing, FAAC, BFT, LiftMaster, and the rest of the nine brands.
Matching the Operator to the Gate
An operator that’s undersized will fail early and a door-sized opener on a driveway gate will burn out. We weigh the gate leaf and check the hinge play before we pick a unit. A heavy gate gets a heavy-duty operator even if the price is higher, because the alternative is a call two winters from now.
Safety Sensors and Reversing
Every powered gate we install gets safety sensors and reversing devices tested against a real obstruction. A gate that doesn’t stop for a car or a person is a lawsuit and a hazard. We test the button, the remote, the loop detector, and the sensor by hand before we hand it back.
Gate Fabrication
Gate Fabrication is custom building or welding a gate that fits an opening no stock gate can match, and it’s what you need when a driveway is a non-standard width, a property line cuts a corner, or a tree means an off-center entry. We fabricate in steel or aluminum, hang the gate on the posts, and weld the hinges, catches, and operator bracket so the gate and the operator are built for each other rather than adapted after the fact. A custom fabrication in Arvada typically runs $2,800-$7,800 depending on material, span, and finish, with the written estimate setting the final price. We don’t cut corners on the hinge side, because a gate that hangs crooked will fight the operator for its whole life. The same install and repair scope applies on Westminster and Lakewood fabrications we plan.
Steel, Aluminum, and Finishes
Steel holds up to a heavier operator and takes paint and powder coat well. Aluminum stays lighter so a mid-range operator can move it and won’t fight the hinge over time. Either way we prime the welds and check the finish before it leaves the fabricator, because a bad finish on a steel gate is rust before the first paid repair call.
Fitting the Gate to the Opening
Fabrication starts with the same measure we use on every install: opening width, post spacing, and grade. The gate is built to that number, not to a nominal width from a supplier sheet. That’s how a custom gate actually closes flush and clears on the first try.
Brands We Service
We work across nine gate brands, and we know where each of them wears. Linear operators appear on a lot of residential openings and their weak point is usually the gearbox over time, not the motor. Viking is a common lift-and-slide platform on longer driveways, and its limit and arm adjustments are what most gates get wrong. Ghost Controls is a residential favorite for swing gates; its control board and sensor wiring are where the failures land. DoorKing is our most-seen commercial platform, and its access control, keypads, and loop detectors need the board set up correctly from the start. FAAC, BFT, Elite, LiftMaster, and Mighty Mule round out the range from entry-level residential to heavy-duty commercial, and we’re not loyal to any one of them: the right repair or install depends on the gate, not the brand badge on the operator.
That cross-brand fluency matters most when a failure could be in the operator, the access control board, the safety sensors, or the gate’s own mechanical structure, and a guess is expensive. We diagnose the actual fault before quoting a fix, and we don’t default to replacing a gate when a component is the problem. Whether you have a DoorKing, a Viking, or any other make, we can help.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Your gate drags or scrapes the ground. A gate that scuffs the driveway or stops halfway has shifted on its posts or lost its hinge alignment, and running it that way stresses the operator. This one gets worse until it’s fixed, so don’t wait it out.
- The gate reverses for no reason or won’t close. A gate that stops and reverses, or refuses to close at all, usually has a failed safety sensor or a control board issue. Both are diagnostic work a generalist shouldn’t guess at, and an unsafe gate that closes on a child is the real risk.
- The operator clicks but nothing moves. A click without travel is a control board, limit, or motor fault, not a remote battery. Each one has a different fix; if the board is fine and the motor is dead, repair or replacement is the next conversation.
- The gate slipped off its track or out of the catch. A slide gate off the track is a heavy panel out of alignment and a crush hazard if it’s under power. Don’t cycle it by hand to test it; get a technician on it before the operator pulls it worse.
- You’re still using a gate that never worked right. A gate that was hung shallow, set on the wrong swing, or paired with the wrong operator will keep failing until it’s fixed at the source. A fresh install or a re-hang is often cheaper than a string of repairs.
Our Process, Step by Step
- 1
Your call and the questions that matter. When you call, we ask the gate type, the operator make and model, and whether it’s a repair or a new install. We answer 24/7 and get the details into the schedule. That means the first visit is planned, not a scouting trip.
- 2
On-site measure and diagnosis. We measure the opening, check the posts and footing depth, test the operator and control board, and inspect the safety sensors and wiring. On a repair, we diagnose the actual fault rather than guessing from the brand.
- 3
The written estimate. You get a clear scope and price in writing before any work starts. That covers what’s being installed or fixed, the operator class if there is one, and the access control. The written estimate sets the final price, and nothing gets added after the fact.
- 4
The scheduled install. Footings, gate, operator, and wiring go in on the same visit when the parts are in hand. If a part needs to be ordered, we tell you the timeline up front and schedule from there. Dispatch runs 7am-7pm, Sunday through Friday.
- 5
Testing and walkthrough. We test the operator, the remote, the keypad, the safety sensors, and the gate’s travel by hand. You get a walkthrough of the controls and the reversing devices, and you know exactly how the gate should behave before you close the driveway.
How Much Does Gate Installation Cost in Arvada?
Gate installation in Arvada is priced per job from a free on-site measure and a written estimate. The ranges below are typical estimates, not final invoices, and the written estimate you get after the measure is what sets the actual price.
- A basic single-swing residential gate with hardware, before automation: $1,900-$4,200.
- Adding a gate opener to a gate that’s already hung: $2,400-$6,500 with power run.
- A full driveway gate with an operator: $3,500-$8,900.
- A sliding gate with cantilever or track hardware and an operator: $4,000-$9,800.
- Custom fabrication in steel or aluminum: $2,800-$7,800 depending on span and finish.
- A full automatic setup including access control and safety devices: $3,800-$9,500.
What moves the price most is the operator class (a Mighty Mule residential unit is a different job than a DoorKing commercial board), the length and weight of the gate, and whether a new power run and footing pour are needed. Access control hardware, keypads, and loop detectors add scope on commercial openings. A gate that has to be fabricated from scratch costs more than one hung to an existing opening.
The way to avoid overpaying is a written scope from a technician who knows the brand. A generic quote that doesn’t specify the operator model, the safety devices, or the power run leaves room for the price to creep. Our free estimate covers the measure, the diagnosis, and the written scope with the operator class named. It’s easier to compare two estimates when both list the same components, and it’s even easier when ours is the only one that does. Pricing questions are free to ask; call (844) 761-1390 for an estimate.
Our Service Area Near Arvada
We install and repair gates across Arvada and the surrounding metro, including Arvada, Westminster, Lakewood, Thornton, Denver, Highlands Ranch, Centennial, Aurora, Fort Lupton, and Lone Tree. The Front Range freeze and thaw and the clay soil are common to most of those neighborhoods, so an install planned for Arvada works the same way a few miles south. Install and measure visits are scheduled Sunday through Friday, 7am to 7pm. If you’re in a neighboring city and aren’t sure we cover it, call and we’ll tell you straight.
Serving Arvada, CO – Our Local Coverage Area
We serve Arvada and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Installation in Arvada
Gate installation is the full job of setting new posts and footings, hanging the gate, and, when you want it automated, mounting the operator and access control and testing the safety devices. It’s a measured, scheduled job rather than a same-day repair. For a job to replace only the operator on a sound gate, see our electric gate repair service.
Most residential installations take one to two days once the hardware is on site, depending on whether footings need to be poured and cured first. A larger sliding or commercial install can take longer, and a custom fabrication adds lead time for the build. We give you a timeline after the on-site measure, before any work starts.
Typical estimates run from about $1,900 for a basic residential swing gate up to $9,800 or more for a full automated sliding gate. The final price depends on the operator class, the gate span, and whether you need a new power run and footing pour. The written estimate sets the final price, and estimates are free. Call (844) 761-1390 for an exact quote.
Yes. We work on nine gate brands, including DoorKing, FAAC, BFT, Linear, Viking, Ghost Controls, Elite, LiftMaster, and Mighty Mule. If an install needs to replace an existing DoorKing board or a Linear operator, we can handle it in the same job. If you just want the existing gate repaired, we diagnose the actual fault before we quote a fix.
Installations are measured, ordered, and scheduled, so they aren’t promised same-day; that’s true of any gate install that needs parts or footing work. Same-day is a repair-side promise, not an install one. We answer 24/7, dispatch runs 7am-7pm, Sunday through Friday, and we’re closed Saturday. A call outside dispatch hours is booked into the next opening.
We stand behind the install and note the covered scope in writing on the estimate so it’s clear before you agree to anything. The specific terms are set per job, so ask at the estimate and we’ll spell out what’s covered and for how long. That’s also where the operator’s own manufacturer coverage gets explained.
Clear the driveway and the ground around the gate location, and note where the closest power source is so we plan the run. If your property has an HOA, bring any size, height, or material rules to the estimate so the gate we build meets them. Beyond that, there’s nothing to prep; the measure and diagnosis are on us.
Schedule Your Gate Installation Service in Arvada Today
If you know the gate type and the brand and want a written price, we can help. Call (844) 761-1390 for a free on-site measure and estimate. We answer 24/7 and dispatch 7am-7pm, Sunday through Friday, so a newly built shell or a busted gate gets a real plan. There’s no obligation, no pressure, and the price you agree to is the price you’ll pay.
Written by the team at Gate Repair Arvada.