Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Electric Gate Repair Across Aurora
When an electric gate in Aurora stops opening, the fix usually sits in one of four places: the operator’s motor, the control board, the safety sensors, or the gate’s own posts and hinges. We work all four. Our technicians have up to experience, and electric gate repair is a specialty here, not a side service. If your gate is stuck open in Hoffman Heights or a keypad entry has quit on a newer build out near 80013, call (844) 761-1390. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Why Aurora Homeowners Call Gate Repair Arvada for Electric Gate Repair
Aurora has a specific gate problem, and it helps to know it before anyone opens a control box. The older subdivisions were built with wooden privacy gates that were nailed together rather than screwed, and every freeze-thaw cycle works those joints loose a little more. Newer master-planned neighborhoods bring automated entrances on quarter-acre lots where the soil underneath is expanding clay. That mix shapes what actually fails here, and it shapes the diagnosis.
We focus on automated gates, full stop. That means circuit boards, control panels, loop detectors, and motor assemblies that general handymen usually decline to touch. It also means we can tell whether the failure lives in the operator, the access control board, the safety sensors, or the mechanical structure, without assuming it’s the brand’s fault. Homeowners and property managers across Aurora call us because they want a technician who recognizes their system before arriving.
Our technicians have up to experience with electric gate systems, and we keep service and installation under one scope so nothing gets handed off to another contractor mid-job. When we come out, we repair first: find the precise failure, then quote the work in writing before anything starts.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Automatic Gate Repair in Aurora
Automatic Gate Repair in Aurora usually starts with the gate that swings fine for nine months and then drags after a wet spring. The job involves checking the hinge post first, correcting sag or resetting a post footing that expansive clay has shifted, then testing the safety photocell and loop detector against the current position of the gate arm. In the older Aurora subdivisions, the operator is often a legacy LiftMaster or Linear unit, and the control board may be obsolete.
What an Aurora homeowner faces is a choice, not a mystery: bring the gate’s mechanics back into line and retrofit safety where the operator allows it, or accept that a pre-2000s operator is past the point of a smart repair. Typical automatic gate repair in Aurora runs $180 to $450 for mechanical correction and sensor work, with control board replacement priced separately. Call us for a written estimate before any work begins.
Hinge and Post Correction on Legacy Wooden Gates
Many original Aurora gates were assembled with nails rather than screws, so the hinge post loosens faster than the rest of the panel. That means a panel-only repair misses the root cause. We reset the post, replace the failing hinge hardware, and check that the gate swings true through its full arc before the operator gets power back.
Safety Sensor and Loop Detector Testing
Entrapment protection has to work before anything else does. We test the safety photocell beam and the loop detector under real conditions, including the residual pull from a sagging gate. A gate that trips on approach is usually reporting a physical problem, not a sensor fault.
Electric Gate Motor in Aurora
Electric Gate Motor work in Aurora often begins with a sound: the motor hums or clicks, but the gate doesn’t move. That points to a stalled motor, a stripped drive gear, or a control board that won’t send a start signal. We test the motor under load, check the wiring run, and confirm the operator’s travel limits before deciding whether the unit can be brought back or should be replaced. Pre-2000s units on older homes in Original Aurora and Hoffman Heights sometimes have obsolete boards, and we’ll tell you plainly when a motor replacement is the cheaper answer.
Typical electric gate motor repair in Aurora runs $250 to $750 for a motor or drive component, and full operator replacement runs $850 to $2,400 depending on the gate size and whether the existing posts can carry the new unit. Every price is written out and agreed before work starts.
Operator Retrofit Versus Replacement
If the gate’s mechanics are sound and the operator’s board and entrapment protection can be brought up to UL 325, a retrofit keeps the existing gate and often saves money. If the board is obsolete or the motor is past its service life, replacing the operator alone, not the whole gate, is usually the cheaper answer. We lay both options out clearly so you can compare them.
Circuit Board, Keypad, and Remote Failures
A dead keypad doesn’t always mean a dead keypad. We trace the fault from the access control board through the wiring to the keypad and remote receiver, then replace only what’s actually failed. That keeps the focus on the exact component rather than a whole operator swap.
Trusted Brands We Service in Aurora
We’re factory-familiar with nine distinct gate brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That range matters in Aurora, where a single street can hold a residential-grade LiftMaster on one property and a heavy-duty FAAC or BFT system on an HOA entrance down the block. We work on your brand, not around it, and we know the common failure points for each operator family before we arrive. Repair comes first; replacement is a recommendation, not a default. Whether your system is residential or commercial, manual or automated, the diagnosis starts the same way.
See the difference
Before
After
Before
After
Before
AfterCommon Electric Gate Repair Problems We See in Aurora Homes
- Nailed gates loosening at the hinge post. In Hoffman Heights and Original Aurora, many original wooden gates were assembled with nails rather than screws, so seasonal freeze-thaw cycling works them loose from the post faster than a screwed gate would. A panel-only fix misses this and the sag returns within a season.
- Clay soil heaving the post footing. Aurora’s expansive clay shifts the post footing after wet springs or drought, which misaligns the operator and trips the safety photocell or loop detector. The gate isn’t broken; the ground moved under it.
- Legacy control boards in pre-2000s operators. A keypad or remote failure on an older LiftMaster or Linear unit can point to a board that’s no longer serviceable. In that case, replacing the operator is often cheaper than chasing a discontinued board.
- Sag that arrives after a spring blizzard. The 80010 – 80014 ZIPs see a pronounced spike in sagging gates and snapped hinges after a typical spring storm. A gate that tolerated winter fine can drop its swing in a single wet week, so a quick check after the thaw saves a bigger repair.
Pricing for Electric Gate Repair in Aurora, CO
Pricing here reflects the two things Aurora homes most often face: aging wooden gates and legacy operators. A routine sensor or hinge fix typically runs $180 to $450. Electric gate motor repair on a residential unit runs $250 to $750, with control board work often bundled in when the board is still serviceable. Full operator replacement for a residential gate runs $850 to $2,400, and commercial-grade systems like DoorKing or FAAC sit at the higher end of that band. What moves the price most is whether the post footing is stable and whether the existing entrapment protection can be brought up to UL 325 without swapping the operator. The estimate is free, the price is per job, and it’s quoted and agreed before any work starts.
We Also Serve Cities Near Aurora
Our electric gate repair team covers Aurora and the surrounding Front Range cities, including Centennial, Denver, Lone Tree, and Highlands Ranch. The gate systems here share the same soil, the same freeze-thaw cycle, and many of the same legacy operators. If you’re outside Aurora city limits but nearby, call and we’ll confirm coverage and timing.
Serving Aurora, CO – Our Local Coverage Area
We serve Aurora and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Electric Gate Repair in Aurora
Yes, usually, if the hinge post and panel are still solid. Nailed gates loosen at the fasteners, not the wood itself, so the fix is to reset the post, replace the nails with proper structural screws, and true the swing before the operator gets power back. If the wood has rotted through at the hinge line, we’ll say so and price replacement honestly rather than patching it. Call (844) 761-1390 for a free estimate.
It does. UL 325 is the safety standard for automated gate operators, and older units often lack the photocell or loop protection that modern systems carry. We check the existing entrapment protection first, then tell you whether the operator’s board can support a retrofit or whether replacement is the cheaper answer. Call (844) 761-1390 for a written quote.
Because the wet weather is moving the ground under your gate, not because the loop detector is broken. Aurora’s expansive clay heaves the post footing after a wet spring, misaligning the operator and pushing the gate into the loop’s detection field. The fix is usually footing correction and swing reset, not a new loop. Call (844) 761-1390 and we’ll schedule a free estimate.
It can often be retrofitted if the rack and the gate’s frame are still true. Retrofitting makes sense when the motor and control board can accept modern safety sensors and the gate travels smoothly through its full arc. If the rack is worn, the frame is bent, or the operator’s board is obsolete, replacement is usually the cheaper answer. Call (844) 761-1390 for an on-site estimate.
Because the hinge post carries the whole gate’s load and takes every freeze-thaw cycle first. Those older gates were often assembled with nails rather than screws, so the joint works loose faster than the panel does, and a sagging gate shows up at the hinge before anywhere else. Fixing the post is what keeps the sag from returning. Call (844) 761-1390 for a free estimate.
Ready to get your gate moving again? Call (844) 761-1390 for a free estimate on electric gate repair in Aurora. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Gate Repair Arvada.