Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Centennial, CO
If you’re planning a new gate for a Centennial property, the job starts with the lot and the HOA, not the catalog. Centennial’s subdivisions went up between the 1970s and 1990s, so the fences and gates here sit on shared rear and side lines that associations manage, and a drive gate has to match the streetscape before it ever moves. We’re a gate specialist, not a fencing or garage door operation: installation, repair, and the electric side of the work, all handled by people who know these systems. Our technicians have up to experience. Call (844) 761-1390. We answer 24/7.
Why Centennial Homes Are Different
Most of Centennial was built out as master-planned subdivisions, and that shapes every gate job here. Wood privacy fencing, decorative metal, and vinyl run along shared property lines, and the associations behind them care about approved styles, stain colors, and hardware. A worn driveway gate in 80111 is often repaired to keep a uniform streetscape, not just to swing again. Then the Front Range does its part: freeze-thaw cycles heave the ground and loosen hinge posts, the high-altitude sun cracks and fades stain, and dry winters open seams in cedar and treated pine. Summer hail and windstorms bend builder-grade steel gates and strip hardware off them. Rear lines frequently back onto greenbelt and trail easements, so a sagging gate on an HOA-maintained fence corridor gets repaired to association spec and coordinated with the association, not only the neighbor next door. That’s the real scope of the work in Centennial.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Main Centennial Services
Installation is the call we get most as Centennial neighborhoods age, but repair and the electric side run a close second, since a lot of the automated gates here are now old enough to need component-level attention.
Gate Repair in Centennial
Repair here means finding the actual failure before recommending anything new. A wood gate that drags in spring is usually a hinge post lifted by frost heave; a steel gate that latches hard after a hail season is usually bent hardware or a shifted frame. We check the operator, the access control board, the safety sensors, and the structure separately so the fix lands on the right part. HOA-spec matching matters on shared corridors, and we work to the association’s style and stain requirements. For a full breakdown of how we handle site work, see Gate Repair in Centennial.

Electric Gate Repair in Centennial
Electric gate repair is a specialty for us, not a side service. Automated gates here run across a wide span of ages, from entry-level residential operators to commercial-grade units on HOA entries and apartment complexes, and a failure can sit in the motor, the control panel, a loop detector, the safety edges, or the mechanical structure itself. We diagnose across brands without guessing. If your Linear or DoorKing operator stopped responding to a remote or a keypad, the answer is usually in the board or the sensor circuit, not the whole gate. More detail lives on our Electric Gate Repair in Centennial page.

Gate Installation in Centennial
Most Centennial subdivisions were finished by the 1990s, which means plenty of original driveway gates and builder-grade operators are at the end of their working life at the same moment. Freeze-thaw heave, dry winters, and hail don’t just wear a gate out; they warp wood panels, crack stain, and bend steel frames until replacement costs less than chasing the damage. That’s where our gate installation work begins: a measured plan for a new gate that fits the lot, the association’s approved look, and how you actually use the entrance.
Driveway Gate Installation
Signs you need it
A driveway gate is ready for replacement in Centennial when the original cedar or treated-pine unit has warped past adjustment, the posts move in their footings, or the steel frame has bent from a wind or hail season and no longer closes squarely.
What it costs in Centennial
Typical driveway gate installation in Centennial runs from about $2,400 to $7,500, depending on whether the gate is a manual swing unit or paired with a new operator, so the written estimate is the number that counts.
How we do it
We measure the opening and the association’s approved style, set new posts to proper footing depth, hang and align the gate, then confirm clear swing and latch before we leave.
Automatic Gate Installation
Signs you need it
You’re ready for an automatic gate when you’re opening a heavy driveway gate by hand on a slope, when the existing operator is a builder-grade unit that’s been failing repeatedly, or when a property needs controlled entry at a shared drive.
What it costs in Centennial
Automatic gate installation in Centennial typically falls between $3,800 and $9,500, and the range widens with operator grade, the power run, and the safety equipment the site needs; the written estimate sets the final price.
How we do it
We size the operator to the gate’s weight and travel, plan the power run to the control panel, install the safety edges and photo sensors, wire the access control, and then test every open and close cycle.
What Gate Installation Costs in Centennial
Installation is scheduled work, not a same-day call, so we measure first and put the price in writing before any material is ordered.
| Item | Typical range in Centennial |
|---|---|
| Manual driveway gate installation | $2,400 – $6,200 |
| Automatic gate installation | $3,800 – $9,500 |
| Sliding gate installation | $3,200 – $8,000 |
Does a new gate in Centennial need HOA or city approval?
Usually yes. Most planned communities here require association sign-off on style, stain, and hardware, and many cities require a permit for a new gate and its footings, so ask your association and the city building department before ordering.
Can you match the gate style my Centennial HOA already requires?
Yes. We measure the existing line, work to the association’s approved style and stain, and confirm the hardware matches what the original streetscape used so the new gate doesn’t stand out along a shared fence corridor.
Brands We Service in Centennial
We work on your brand, not one company’s line: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, from entry-level residential operators like Ghost Controls to commercial-grade DoorKing and FAAC systems. Cross-brand diagnosis is the point, so we don’t assume a failure comes from the brand we know best. See our brands for the full list. Parts sourcing varies by operator, so turnaround depends on the unit.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Centennial, CO
These ranges reflect what the work typically runs in this market. The written estimate you get after we look at the gate is the final word, and the price is quoted and agreed before any work starts.
| Service | Typical range in Centennial |
|---|---|
| Manual driveway gate installation | $2,400 – $6,200 |
| Automatic gate installation | $3,800 – $9,500 |
| Sliding gate installation | $3,200 – $8,000 |
| Gate repair call | $150 – $450 |
| Hinge and post repair | $180 – $550 |
| Electric gate repair | $200 – $650 |
| Control board replacement | $300 – $800 |
| Safety sensor and loop detector diagnostics | $150 – $500 |
| Gate operator motor repair | $350 – $1,100 |
What pushes price up in Centennial is usually the structure, not the parts: frost-heaved posts that need re-set footings, HOA-spec matching on a shared fence corridor, and commercial-grade operators on multi-unit entries. On the electric side, control boards and loop detectors raise the figure faster than a hinge or latch fix. Whatever the total, you’ll have it in writing before we touch the gate.
Neighborhoods We Serve in Centennial
We cover Centennial from the older planned subdivisions in the west to the newer-looking streets near the eastern edge, and the same freeze-thaw and hail conditions show up across all of it. One scheduling note applies to the whole city: fast dispatch from 7am to 7pm, Sunday through Friday, and we’re closed Saturday. If a gate fails on a Saturday, call and we’ll book it into the next opening.
- Willow Creek
- Foxridge
- Greenwood Village-adjacent streets in 80111
- Southglenn area
- Smoky Hill
Service Area – Cities Near Centennial
Centennial sits in the south metro corridor, and our gate work runs outward from here to the surrounding communities. If you’re just outside the city line, we can usually still help. We regularly cover Lone Tree, CO to the southeast, Highlands Ranch, CO to the southwest, Aurora, CO to the east, and Denver, CO to the north. Call us with your address and we’ll confirm coverage and scheduling before you commit to anything.
Serving Centennial, CO – Our Local Coverage Area
We serve Centennial and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Gate Company in Centennial
Yes, we cover the whole city, from the 80111 streets near the Denver line down through the older subdivisions in 80122 and the Smoky Hill side. Call (844) 761-1390 with your address and we’ll confirm the schedule. Estimates are free.
We answer 24/7 and run fast dispatch from 7am to 7pm, Sunday through Friday, closed Saturday. A call outside dispatch hours is booked into the next opening. Emergency pricing doesn’t jump; the written estimate is the same number.
We do. Since so many Centennial property lines back onto HOA-maintained fence corridors and greenbelts, we work to the association’s approved style, stain, and hardware, and we can walk the association through the repair so the gate meets spec.
If you need a gate installed, repaired, or brought back to life, call (844) 761-1390 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
What happens when you call
- 1A real person answersNo phone trees. Talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically the same day.
- 4You approve before work beginsNothing starts until you say go.
What Centennial Customers Say
"Hinge post had rotted at the base and the whole swing gate was sagging into the concrete. He rebuilt the post rather than talking us into a whole new gate, which two other companies had pushed for."
- Amanda Ziegler"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
- Ebony Jackson"Gate works properly now and the price was fair. The one thing is that it took two visits, because the operator model we have is old and the part had to be ordered. They didn't charge for the second trip."
- Diego Herrera